Unused flat roof, Substrate wood, sealed with high polymer, freely weathered

High polymer of the coating
GLAPOR flex hot bitumen
GLAPOR foam glass plates
GLAPOR flex hot bitumen
Separation layer on wooden formwork
wood construction

Description of the application

The GLAPOR flat roof on a wooden substructure is a compact and under flow secured bonded flat roof construction.

The thermal insulation is installed free of thermal bridges using GLAPOR flex hot bitumen or GLAPOR k-2k cold adhesive on the substructure.

The sealing system conforms to the legal and normative regulations for the respected. The GLAPOR tapered system has different slopes available.

To avoid concentrated drainage GLAPOR roof riders are available in different versions.

Advantages of the GLAPOR flat roof systems:

Quality: Cellular glass products manufactured with proprietary technology and professional quality control.

Service: Expert advice from planners, structural engineers, construction experts and contractors.

Efficiency: Very long service life of the system constructions with minimum maintenance.

Sustainability: Made from 100% recycled glass, we guarantee consistent material properties over the entire usage time.

Safety: GLAPOR cellular glass insulation panels are diffusion-tight. When installed with closed joints, a vapor barrier is not required.

Read less

Planning notes / Execution notes

A vapor barrier is not required when using GLAPOR cellular glass insulations because GLAPOR cellular glass boards are vapor-tight.

The underground should be level, gem. DIN 18 202, designed to be load bearing and dry and free from residues (oil, grease, etc).

10 kN / m² can be assumed without proof for the wind resistance of fully glued roof systems with GLAPOR foam glass and GLAPOR flex hot bitumen.

Fire protection “Hard roofing” according to DIN 4102-7 – Cellular glass panels belong to building material class A1. The thermal insulation is not flammable. For the component “roof”, the state building regulations require, in addition to the classification in a buidling material class (A1) usually a so-called “hard roofing”. This is to ensure that the roof structures are resistant to spreading fire and radiant heat. For the manufacturers of waterproofing systems, these tests with the different seals are available.

At the blanking is a space condition out of bitumen roof lane to confused or to transfix, for example G 200 DD sanded, or a systeme lane for this use.

Nail picture and nail distance take out of the processing rules of the lane producer. DIN 1055 – part 4 wind forces, consider to building geometry.

The thickness of the cellular glass insulation comply with the lawful and object-specific requirements of the heat transmission (U-value of the element). Please check our data sheets.

The minimum thickness of the thermal insulation is 40mm. Tapered insulation systems starts by a thickness of 30mm. With a multi-ply shift were the insulations boards stick together among each other with GLAPOR flex hot bitumen. The use of the bonding with the insulations boards among each other is ca 2-3 kg GLAPOR flex hot bitumen.

The use of the bonding with the insulations boards on the underground is conditional on his evenness and is ca. 5-8 kg GLAPOR flex hot bitumen. The overlaying of ridges and throats were processed by emery boards by the shift of the tapered insulation systems.

The minimum roof pitch of 2% should be aspire. Roof pitches under 2% are special construction and need a special shift of tightening lanes.

The processing temperature of the bitumen is ca. 150-180°C.

The flat roof rules and regulations of the tightening lane producers are important for the shift of tightening lanes. If you use a rich polymer single-layer tightening, you need a hot bitumen drain at the GLAPOR cellular glass boards. The use is ca. 2,0 kg/m² roof area.

Read less

Verarbeitungshinweise

Clean the wooden roof surface and install a suitable separating layer on the wooden surface. Nail off according to wind load requirements.
For example: nail bitumen sheet with overlap.

Pour GLAPOR flex hot bitumen.
Consumption 5-8 kg / m² depending on the evenness of the underground.

Pour GLAPOR flex hot bitumen, Immerse the insulation boards with two sides in the adhesive.

Insert diagonally so that the longitudinal andtransverse joints are filled with bitumen.
For a short time, sevure the insulation board against movement.

Pour GLAPOR flex hot bitumen paste and spread with a rubber spatula on the cellular glass surface as a cell-filling top coat.
Consumption about 2 kg / m²

Install high-polymer seal.
Please note the instructions of the Manufacturer.
Other sealing systems on request.